Just about every person has their own individual rationale with regards to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also in some cases, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard task. If the old bathtub is conveniently easily accessible, the job can move rapidly; if you need to open a wall surface to get rid of the old bathtub and also position the new bathtub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will need an assistant to leave the old tub and embeded in the new one. Make certain you have qualified yourself for the task and also are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed task, it is far better to consider utilizing one before you start. Chances are you may need a specialist plumber to make tube links.
This write-up will certainly help you set up a brand-new bath tub in your washroom if you have already purchased a brand-new bathtub and do not require to transform the arrangement of your previous water pipes.
Your tools and also product list must consist of the following:
Getting ready for the Setup
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final position.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of removing the existing taps can be fairly troublesome due to the limited access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before going on to fit the new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed setting. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the level checks out level.
To set up faucets, fit all-time low of the outermost flexible faucet port to the proper supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water supply and check all joints and new pipework for leakages as well as tighten them if required. Fill the bath tub as well as additionally inspect the overflow electrical outlet and the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the bath tub should wait till the bathtub has been made use of at the very least when as this will settle it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin making certain that the washers are in area between the tap and also the sink. Safeguard the faucet in position with the maker offered backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous type should be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can crack rather very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the market. It is recommended to fit the floor tiles making use of waterproof or water-proof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that piece of content was essential. Liked our review? Please share it. Let others locate it. I take joy in reading our article about Installing A Bathtub.
Immediate plumbing assistance for emergencies.